Load data for .30 PICRA + .308 | 165gr | Hornady SP

Recommended Powder(s): none

Load Specifications

(Use the Personalized Load Calculator below to adjust )

Bullet:	.308 \| 165gr \| Hornady SP
Manufacturer SKU:	3040
Bullet Weight:	165gr \| 10.7g
Bullet Diameter:	0.308" \| 7.82mm
Bullet Length:	1.152" \| 29.3mm
Caliber:	.30 PICRA load data
Case Length (l3):	1.291" \| 32.8mm
Cartridge Length (C.O.L.):	2.172" \| 55.2mm
Seated Depth:	0.271" \| 6.9mm
Shank Seated Depth:	0.271" \| 6.9mm
Case Capacity:	24.2 Grains of Water \| 1.57 cm³
Primer Size:	Small Pistol (SP)
Max. allowed Pressure:	40611 psi \| 2800 bar
LID:	LID_B2683_C311
Last updated:	2025-01-01

Load data for 46 loads in caliber .30 PICRA with .308 | 165gr | Hornady SP bullet and 23 powders such as none. The key underlying parameters are shown in the table above.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service.

Questions regarding the load data: Please read the information in the next tab "Explanations".
A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed".

Our load data might deviate from other sources - see the "most common reasons for deviations".

All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions" if you deviate.

You can set your specifications in the "Personalized Load Calculator".

Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric)
No data yet
C.O.L. (Inch)
C.O.L. (mm)
We recommend you limit powder range to relevant brands to speed up re-calculation of results
Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section.

Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables.
Case Length (Inch)
Case Length (mm)
CaseCapacity (GoW)
Min z (%)
Min FR (%)
Max FR*
Barrel Length (Inch)
Barrel Length (cm)
Safety Buffer (%)
.

Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there.

Powder	Charge	FR	MaxP	%	V(0)	z
ADI AP 100	<<locked>>	71%	34635	85%	**78	100%
ADI APS 450	<<locked>>	64%	36405	90%	**1	100%
Accurate 4100	<<locked>>	73%	35853	88%	**76	92%
[Accurate No. 11 FS]*	<<locked>>	81%	35549	88%	**83	85%
Accurate TCM	<<locked>>	63%	36448	90%	**63	98%
Alliant 2400	<<locked>>	70%	36521	90%	**93	95%
Alliant BLUE DOT	<<locked>>	72%	35592	88%	**50	99%
[Hodgdon H110]*	<<locked>>	77%	35824	88%	**12	89%
Hodgdon LilGun	<<locked>>	77%	34534	85%	**22	95%
Hodgdon TrailBoss	<<locked>>	96%	25483	63%	**3	100%
Maxam CSB 1	<<locked>>	64%	35230	87%	**50	100%
Ramshot Enforcer	<<locked>>	69%	35346	87%	**76	95%
ReloadSwiss RS 14	<<locked>>	97%	24990	62%	**2	100%
ReloadSwiss RS 30	<<locked>>	94%	35969	89%	**35	92%
SNPE Vectan A0	<<locked>>	64%	36332	89%	**99	100%
SNPE Vectan BA6 1/2	<<locked>>	95%	35302	87%	**73	97%
SNPE Vectan BA7 1/2	<<locked>>	66%	34693	85%	**38	100%
[Somchem S265]*	<<locked>>	84%	34650	85%	**40	87%
Vihtavuori 3N38	<<locked>>	68%	34853	86%	**14	100%
Vihtavuori N105	<<locked>>	70%	34577	85%	**27	100%
Vihtavuori N110	<<locked>>	86%	34635	85%	**86	95%
Vihtavuori N32C Tin Star	<<locked>>	79%	36085	89%	**4	100%
[Winchester 296]*	<<locked>>	77%	36172	89%	**25	85%

Max Load - Barrel Length: 5.50''

Powder	Charge	FR	MaxP	%	V(0)	z
ADI AP 100	<<locked>>	61%	26252	65%	**63	100%
ADI APS 450	<<locked>>	60%	33808	83%	**8	100%
[Accurate 4100]*	<<locked>>	61%	24192	60%	**89	85%
[Accurate No. 11 FS]*	<<locked>>	75%	28340	70%	**78	80%
Accurate TCM	<<locked>>	61%	34418	85%	**43	97%
Alliant 2400	<<locked>>	61%	27151	67%	**48	90%
Alliant BLUE DOT	<<locked>>	61%	26237	65%	**09	96%
[Hodgdon H110]*	<<locked>>	64%	23366	58%	**99	81%
[Hodgdon LilGun]*	<<locked>>	61%	19087	47%	**43	83%
Hodgdon TrailBoss	<<locked>>	60%	13329	33%	**6	100%
Maxam CSB 1	<<locked>>	61%	32779	81%	**27	100%
Ramshot Enforcer	<<locked>>	61%	26498	65%	**38	91%
ReloadSwiss RS 14	<<locked>>	61%	13402	33%	**6	100%
[ReloadSwiss RS 30]*	<<locked>>	75%	20856	51%	**60	80%
SNPE Vectan A0	<<locked>>	61%	33852	83%	**73	100%
[SNPE Vectan BA6 1/2]*	<<locked>>	61%	14011	35%	**3	81%
SNPE Vectan BA7 1/2	<<locked>>	61%	30516	75%	**89	100%
[Somchem S265]*	<<locked>>	72%	25150	62%	**96	81%
Vihtavuori 3N38	<<locked>>	61%	28587	70%	**25	99%
Vihtavuori N105	<<locked>>	61%	26063	64%	**06	100%
[Vihtavuori N110]*	<<locked>>	61%	16389	40%	**8	81%
Vihtavuori N32C Tin Star	<<locked>>	61%	25092	62%	**0	100%
[Winchester 296]*	<<locked>>	69%	27630	68%	**91	80%

Start Load - Barrel Length: 5.50''

Any powder missing? Then click here.

FR ... fill rate of the cartridge in percent

MaxP ... max. pressure of load in psi or bar

% ... max. pressure of load in percent of the maximum allowed pressure for this caliber

V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s)

z ... powder burnt in percent

[...] *... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads.

[...] ²... fill rate low - you might want to consider using a filler to ensure proper ignition.

[...] ᴾ... possible press load - work up slowly to this load while watching for signs of excessive pressure.

👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance.

<<locked>>... you need to buy an access license to unlock the data